Skip to content

Commit 0016306

Browse files
jeromecoutantjeromecoutant
committed
STM32 NUCLEO boards with Ethernet connector: solve conflict with D11 arduino pin
If you are using Ethernet, and not SPI Arduino pins: => keep your board with the default configuration If you are using SPI Arduino pins, and not Ethernet: => you should remove the JP6 bridge on the front side of the board If you need SPI Arduino and Ethernet: => you have to patch the NUCLEO board on the back side: set solder bridge SB121 to off, and SB122 to on => D11 is no more connected to PA_7 but to PB_5 => overwrite d11_configuration config value in json file
1 parent 0c2af26 commit 0016306

File tree

13 files changed

+150
-69
lines changed

13 files changed

+150
-69
lines changed

‎targets/TARGET_STM/TARGET_STM32F2/TARGET_NUCLEO_F207ZG/PeripheralPins.c

Lines changed: 10 additions & 8 deletions
Original file line numberDiff line numberDiff line change
@@ -57,8 +57,8 @@ const PinMap PinMap_ADC[] = {
5757
{PA_5_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 // choice: PA_5 with ADC_1
5858
{PA_6_ALT0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 // choice: PA_6 with ADC_2
5959
{PA_6, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6
60-
// {PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 // Ethernet RMII RX Data Valid
61-
// {PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 // Ethernet RMII RX Data Valid
60+
{PA_7_ALT0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 // Ethernet RMII RX Data Valid - used when JP6 ON - choice: PA_7 with ADC_2
61+
{PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 // Ethernet RMII RX Data Valid - used when JP6 ON - choice: PA_7 with ADC_2
6262
// {PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 // LED1
6363
// {PB_0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8 // LED1
6464
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
@@ -142,10 +142,10 @@ const PinMap PinMap_PWM[] = {
142142
{PA_5, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N
143143
{PA_6, PWM_13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1
144144
{PA_6_ALT0, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 // choice: PA_6 with PWM_13
145-
// {PA_7, PWM_14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 // Ethernet RMII RX Data Valid
146-
// {PA_7, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N // Ethernet RMII RX Data Valid
147-
// {PA_7, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 // Ethernet RMII RX Data Valid
148-
// {PA_7, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N // Ethernet RMII RX Data Valid
145+
{PA_7, PWM_14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 // Ethernet RMII RX Data Valid - used when JP6 ON - choice: PA_7 with PWM_14
146+
{PA_7_ALT0, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N // Ethernet RMII RX Data Valid - used when JP6 ON - choice: PA_7 with PWM_14
147+
{PA_7_ALT1, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 // Ethernet RMII RX Data Valid - used when JP6 ON - choice: PA_7 with PWM_14
148+
{PA_7_ALT2, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N // Ethernet RMII RX Data Valid - used when JP6 ON - choice: PA_7 with PWM_14
149149
// {PA_8, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 // USB SOF
150150
// {PA_9, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 // USB VBUS
151151
// {PA_10, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 // USB ID
@@ -263,8 +263,10 @@ const PinMap PinMap_UART_CTS[] = {
263263
//*** SPI ***
264264

265265
const PinMap PinMap_SPI_MOSI[] = {
266-
{PA_7, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // Ethernet RMII RX Data Valid // D11
267-
{PB_5, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
266+
{PA_7, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // Ethernet RMII RX Data Valid - used when JP6 ON - ARDUINO D11 (default configuration)
267+
{PB_5, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // ARDUINO D11 (need HW and SW updates)
268+
// HW solder bridge update : SB121 off, SB122 on
269+
// SW : config from json files
268270
// {PB_5, SPI_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, // choice: PB_5 with SPI_1
269271
{PB_15, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
270272
{PC_3, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},

‎targets/TARGET_STM/TARGET_STM32F2/TARGET_NUCLEO_F207ZG/PinNames.h

Lines changed: 4 additions & 1 deletion
Original file line numberDiff line numberDiff line change
@@ -58,6 +58,9 @@ typedef enum {
5858
PA_6 = 0x06,
5959
PA_6_ALT0 = 0x06|ALT0,
6060
PA_7 = 0x07,
61+
PA_7_ALT0 = 0x07|ALT0,
62+
PA_7_ALT1 = 0x07|ALT1,
63+
PA_7_ALT2 = 0x07|ALT2,
6164
PA_8 = 0x08,
6265
PA_9 = 0x09,
6366
PA_10 = 0x0A,
@@ -218,7 +221,7 @@ typedef enum {
218221
D8 = PF_12,
219222
D9 = PD_15,
220223
D10 = PD_14,
221-
D11 = PA_7,
224+
D11 = STM32_D11_SPI_ETHERNET_PIN, /* config in targets.json file */
222225
D12 = PA_6,
223226
D13 = PA_5,
224227
D14 = PB_9,

‎targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_NUCLEO_F429ZI/PeripheralPins.c

Lines changed: 17 additions & 11 deletions
Original file line numberDiff line numberDiff line change
@@ -57,8 +57,8 @@ const PinMap PinMap_ADC[] = {
5757
// {PA_5, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 - ARDUINO D13
5858
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 - ARDUINO D12
5959
// {PA_6, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 - ARDUINO D12
60-
// {PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 (pin used by ethernet when JP6 ON) - ARDUINO D11
61-
{PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 (pin used by ethernet when JP6 ON) - ARDUINO D11
60+
// {PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
61+
{PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
6262
// {PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 (pin used by LED1)
6363
// {PB_0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8 (pin used by LED1)
6464
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
@@ -140,12 +140,12 @@ const PinMap PinMap_PWM[] = {
140140
// {PA_3, PWM_9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 - ARDUINO A0
141141
// {PA_5, PWM_2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 - ARDUINO D13
142142
{PA_5, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N - ARDUINO D13
143-
// {PA_6, PWM_13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1 - ARDUINO D12
143+
// {PA_6, PWM_13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1 - ARDUINO D12
144144
{PA_6, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 - ARDUINO D12
145-
{PA_7, PWM_14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 (pin used by ethernet when JP6 ON) - ARDUINO D11
146-
// {PA_7, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N (pin used by ethernet when JP6 ON) - ARDUINO D11
147-
// {PA_7, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 (pin used by ethernet when JP6 ON) - ARDUINO D11
148-
// {PA_7, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N (pin used by ethernet when JP6 ON) - ARDUINO D11
145+
{PA_7, PWM_14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
146+
// {PA_7, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
147+
// {PA_7, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
148+
// {PA_7, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
149149
{PA_8, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
150150
// {PA_9, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 (pin used by usb)
151151
// {PA_10, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 (pin used by usb)
@@ -159,7 +159,9 @@ const PinMap PinMap_PWM[] = {
159159
{PB_1, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 1)}, // TIM8_CH3N
160160
{PB_3, PWM_2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
161161
{PB_4, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
162-
{PB_5, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
162+
{PB_5, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 - ARDUINO D11 (need HW and SW updates)
163+
// HW solder bridge update : SB121 off, SB122 on
164+
// SW : config from json files
163165
{PB_6, PWM_4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
164166
// {PB_7, PWM_4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 (pin used by LED2)
165167
// {PB_8, PWM_10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1 - ARDUINO D15
@@ -268,8 +270,10 @@ const PinMap PinMap_UART_CTS[] = {
268270
//*** SPI ***
269271

270272
const PinMap PinMap_SPI_MOSI[] = {
271-
{PA_7, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // (pin used by ethernet when JP6 ON) - ARDUINO D11
272-
{PB_5, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
273+
{PA_7, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // pin used by ethernet when JP6 ON - ARDUINO D11 (default configuration)
274+
{PB_5, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // ARDUINO D11 (need HW and SW updates)
275+
// HW solder bridge update : SB121 off, SB122 on
276+
// SW : config from json files
273277
// {PB_5, SPI_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
274278
{PB_15, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
275279
{PC_3, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, // ARDUINO A2
@@ -330,7 +334,9 @@ const PinMap PinMap_CAN_RD[] = {
330334
{PB_8, CAN_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
331335
{PB_12, CAN_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
332336
{PD_0, CAN_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
333-
{PB_5 , CAN_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
337+
{PB_5 , CAN_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)}, // ARDUINO D11 (need HW and SW updates)
338+
// HW solder bridge update : SB121 off, SB122 on
339+
// SW : config from json files
334340
{PA_11, CAN_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
335341
{NC, NC, 0}
336342
};

‎targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_NUCLEO_F429ZI/PinNames.h

Lines changed: 1 addition & 1 deletion
Original file line numberDiff line numberDiff line change
@@ -183,7 +183,7 @@ typedef enum {
183183
D8 = PF_12,
184184
D9 = PD_15,
185185
D10 = PD_14,
186-
D11 = PA_7,
186+
D11 = STM32_D11_SPI_ETHERNET_PIN, /* config in targets.json file */
187187
D12 = PA_6,
188188
D13 = PA_5,
189189
D14 = PB_9,

‎targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_NUCLEO_F439ZI/PeripheralPins.c

Lines changed: 17 additions & 11 deletions
Original file line numberDiff line numberDiff line change
@@ -57,8 +57,8 @@ const PinMap PinMap_ADC[] = {
5757
// {PA_5, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 - ARDUINO D13
5858
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 - ARDUINO D12
5959
// {PA_6, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 - ARDUINO D12
60-
// {PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 (pin used by ethernet when JP6 ON) - ARDUINO D11
61-
{PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 (pin used by ethernet when JP6 ON) - ARDUINO D11
60+
// {PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
61+
{PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
6262
// {PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 (pin used by LED1)
6363
// {PB_0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8 (pin used by LED1)
6464
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
@@ -140,12 +140,12 @@ const PinMap PinMap_PWM[] = {
140140
// {PA_3, PWM_9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 - ARDUINO A0
141141
// {PA_5, PWM_2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 - ARDUINO D13
142142
{PA_5, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N - ARDUINO D13
143-
// {PA_6, PWM_13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1 - ARDUINO D12
143+
// {PA_6, PWM_13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1 - ARDUINO D12
144144
{PA_6, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 - ARDUINO D12
145-
{PA_7, PWM_14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 (pin used by ethernet when JP6 ON) - ARDUINO D11
146-
// {PA_7, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N (pin used by ethernet when JP6 ON) - ARDUINO D11
147-
// {PA_7, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 (pin used by ethernet when JP6 ON) - ARDUINO D11
148-
// {PA_7, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N (pin used by ethernet when JP6 ON) - ARDUINO D11
145+
{PA_7, PWM_14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
146+
// {PA_7, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
147+
// {PA_7, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
148+
// {PA_7, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N (pin used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
149149
{PA_8, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
150150
// {PA_9, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 (pin used by usb)
151151
// {PA_10, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 (pin used by usb)
@@ -159,7 +159,9 @@ const PinMap PinMap_PWM[] = {
159159
{PB_1, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 1)}, // TIM8_CH3N
160160
{PB_3, PWM_2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
161161
{PB_4, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
162-
{PB_5, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
162+
{PB_5, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 - ARDUINO D11 (need HW and SW updates)
163+
// HW solder bridge update : SB121 off, SB122 on
164+
// SW : config from json files
163165
{PB_6, PWM_4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
164166
// {PB_7, PWM_4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 (pin used by LED2)
165167
// {PB_8, PWM_10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1 - ARDUINO D15
@@ -268,8 +270,10 @@ const PinMap PinMap_UART_CTS[] = {
268270
//*** SPI ***
269271

270272
const PinMap PinMap_SPI_MOSI[] = {
271-
{PA_7, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // (pin used by ethernet when JP6 ON) - ARDUINO D11
272-
{PB_5, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
273+
{PA_7, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // pin used by ethernet when JP6 ON - ARDUINO D11 (default configuration)
274+
{PB_5, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, // ARDUINO D11 (need HW and SW updates)
275+
// HW solder bridge update : SB121 off, SB122 on
276+
// SW : config from json files
273277
// {PB_5, SPI_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
274278
{PB_15, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
275279
{PC_3, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, // ARDUINO A2
@@ -330,7 +334,9 @@ const PinMap PinMap_CAN_RD[] = {
330334
{PB_8, CAN_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
331335
{PB_12, CAN_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
332336
{PD_0, CAN_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
333-
{PB_5 , CAN_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
337+
{PB_5 , CAN_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)}, // ARDUINO D11 (need HW and SW updates)
338+
// HW solder bridge update : SB121 off, SB122 on
339+
// SW : config from json files
334340
{PA_11, CAN_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
335341
{NC, NC, 0}
336342
};

‎targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_NUCLEO_F439ZI/PinNames.h

Lines changed: 1 addition & 1 deletion
Original file line numberDiff line numberDiff line change
@@ -183,7 +183,7 @@ typedef enum {
183183
D8 = PF_12,
184184
D9 = PD_15,
185185
D10 = PD_14,
186-
D11 = PA_7,
186+
D11 = STM32_D11_SPI_ETHERNET_PIN, /* config in targets.json file */
187187
D12 = PA_6,
188188
D13 = PA_5,
189189
D14 = PB_9,

0 commit comments

Comments
 (0)