Merge pull request #8083 from ARMmbed/release-candidate

Release candidate for mbed-os-5.10.0-rc2

Author: adbridge

TESTS/netsocket/README.md

@@ -21,8 +21,8 @@ You need Icetea and mbed-cli that supports Icetea, installed.
 
 Depending on a device, there might be a default network interface type defined in the mbed-os/targets/targets.json, which is used to locate a test-config file by default. 
 If there is not, or you want to use a different interface than the default, you need to provide a relevant test-config -file to the mbed test with --test-config option.
-The test-config file contains the necessary information for the test application, there are some test-config files located under mbed-os/tools/test-configs.
-Devices which have their network drivers residing inside mbed-os can use generic test-configs like HeapBlockDeviceAndEthernetInterface.json and HeapBlockDeviceAndWifiInterface.json. Otherwise you need to use a device specific test-config.
+The test-config file contains the necessary information for the test application, there are some test-config files located under mbed-os/tools/test_configs.
+Devices which have their network drivers residing inside mbed-os can use generic test_configs like HeapBlockDeviceAndEthernetInterface.json and HeapBlockDeviceAndWifiInterface.json. Otherwise you need to use a device specific test-config.
 
 ### Running the tests
 
@@ -42,10 +42,10 @@ Some devices may offer multiple network interfaces to operate with. For example,
 The tests can be run for either one of those using already existing test-config -files.
 
 To run the tests with Wi-Fi interface:
-`>mbed test -m UBLOX_EVK_ODIN_W2 -t <toolchain> --icetea --test-config tools/test-configs/HeapBlockDeviceAndWifiInterface.json`
+`>mbed test -m UBLOX_EVK_ODIN_W2 -t <toolchain> --icetea --test-config tools/test_configs/HeapBlockDeviceAndWifiInterface.json`
 
 To run the tests with ethernet interface:
-`>mbed test -m UBLOX_EVK_ODIN_W2 -t <toolchain> --icetea --test-config tools/test-configs/HeapBlockDeviceAndEthernetInterface.json`
+`>mbed test -m UBLOX_EVK_ODIN_W2 -t <toolchain> --icetea --test-config tools/test_configs/HeapBlockDeviceAndEthernetInterface.json`
 
 #### Providing Wi-Fi access point information
 

TESTS/netsocket/eth_environment.png

@@ -69,17 +69,17 @@ pip install "gcovr>=4.1"
 
 > In case of running into problems see [troubleshooting](#troubleshooting) section.
 
-`UNITTESTS/mbed_unittest.py` contains testing scripts for Mbed OS unit testing. Mbed CLI supports unit testing through `mbed unittest` command with the same arguments.
+`UNITTESTS/mbed_unittest.py` contains testing scripts for Mbed OS unit testing. Mbed CLI supports unit testing through `mbed test --unittests` command with the same arguments.
 
 ### Testing with Mbed CLI
 
 ```
-mbed unittest
+mbed test --unittests
 ```
 
 A subset of tests can be run by providing `-r` flag for the tool which runs tests matching a regular expression.
 
-e.g. `mbed unittest --run -r features_netsocket`
+e.g. `mbed test --unittests --run -r features_netsocket`
 
 ### Build manually without Python tools
 
@@ -144,7 +144,7 @@ Run ctest dashboard test and create test results:
 
 Python tools use gcovr to build code coverage reports. Generate html report `UNITTESTS/build/coverage/index.html` with:
 ```
-mbed unittest --coverage html
+mbed test --unittests --coverage html
 ```
 
 To get coverage for a single test suite, run gcovr separately for suite coverage data directory. See [gcovr documentation](https://gcovr.com/guide.html#filter-options) for more information.
@@ -211,10 +211,10 @@ A unit test definition file `unittest.cmake` requires variables to be set for a
 #### Creating unit tests files with Mbed CLI
 
 ```
-mbed unittest --new <FILEPATH>
+mbed test --unittests --new <FILEPATH>
 ```
 
-E.g. `mbed unittest --new rtos/Semaphore.cpp`
+E.g. `mbed test --unittests --new rtos/Semaphore.cpp`
 
 The generator script only creates the files required for a unit test. It does not write unit tests automatically nor does it handle source dependencies.
 

TESTS/netsocket/wifi_environment.png

@@ -27,7 +27,12 @@ rtos::Mutex::~Mutex()
     return;
 }
 
-osStatus rtos::Mutex::lock(unsigned int)
+osStatus rtos::Mutex::lock(void)
+{
+    return osOK;
+}
+
+osStatus rtos::Mutex::lock(uint32_t millisec)
 {
     return osOK;
 }

TEST_APPS/readme.md

@@ -34,6 +34,14 @@ MbedCRC<POLY_32BIT_ANSI, 32>::MbedCRC():
     mbed_crc_ctor();
 }
 
+template<>
+MbedCRC<POLY_32BIT_REV_ANSI, 32>::MbedCRC():
+    _initial_value(~(0x0)), _final_xor(~(0x0)), _reflect_data(false), _reflect_remainder(false),
+    _crc_table((uint32_t *)Table_CRC_32bit_Rev_ANSI)
+{
+    mbed_crc_ctor();
+}
+
 template<>
 MbedCRC<POLY_16BIT_IBM, 16>::MbedCRC():
     _initial_value(0), _final_xor(0), _reflect_data(true), _reflect_remainder(true),

UNITTESTS/README.md

@@ -275,7 +275,7 @@ class MbedCRC {
             p_crc = (uint32_t)(p_crc << (8 - width));
         }
         // Optimized algorithm for 32BitANSI does not need additional reflect_remainder
-        if ((TABLE == _mode) && (POLY_32BIT_ANSI == polynomial)) {
+        if ((TABLE == _mode) && (POLY_32BIT_REV_ANSI == polynomial)) {
             *crc = (p_crc ^ _final_xor) & get_crc_mask();
         } else {
             *crc = (reflect_remainder(p_crc) ^ _final_xor) & get_crc_mask();
@@ -415,7 +415,6 @@ class MbedCRC {
     int32_t bitwise_compute_partial(const void *buffer, crc_data_size_t size, uint32_t *crc) const
     {
         MBED_ASSERT(crc != NULL);
-        MBED_ASSERT(buffer != NULL);
 
         const uint8_t *data = static_cast<const uint8_t *>(buffer);
         uint32_t p_crc = *crc;
@@ -460,7 +459,6 @@ class MbedCRC {
     int32_t table_compute_partial(const void *buffer, crc_data_size_t size, uint32_t *crc) const
     {
         MBED_ASSERT(crc != NULL);
-        MBED_ASSERT(buffer != NULL);
 
         const uint8_t *data = static_cast<const uint8_t *>(buffer);
         uint32_t p_crc = *crc;
@@ -480,9 +478,17 @@ class MbedCRC {
             }
         } else {
             uint32_t *crc_table = (uint32_t *)_crc_table;
-            for (crc_data_size_t i = 0; i < size; i++) {
-                p_crc = (p_crc >> 4) ^ crc_table[(p_crc ^ (data[i] >> 0)) & 0xf];
-                p_crc = (p_crc >> 4) ^ crc_table[(p_crc ^ (data[i] >> 4)) & 0xf];
+            if (POLY_32BIT_REV_ANSI == polynomial) {
+                for (crc_data_size_t i = 0; i < size; i++) {
+                    p_crc = (p_crc >> 4) ^ crc_table[(p_crc ^ (data[i] >> 0)) & 0xf];
+                    p_crc = (p_crc >> 4) ^ crc_table[(p_crc ^ (data[i] >> 4)) & 0xf];
+                }
+            }
+            else {
+                for (crc_data_size_t byte = 0; byte < size; byte++) {
+                    data_byte = reflect_bytes(data[byte]) ^ (p_crc >> (width - 8));
+                    p_crc = crc_table[data_byte] ^ (p_crc << 8);
+                }
             }
         }
         *crc = p_crc & get_crc_mask();
@@ -497,6 +503,11 @@ class MbedCRC {
         MBED_STATIC_ASSERT(width <= 32, "Max 32-bit CRC supported");
 
 #ifdef DEVICE_CRC
+        if (POLY_32BIT_REV_ANSI == polynomial) {
+            _crc_table = (uint32_t *)Table_CRC_32bit_Rev_ANSI;
+            _mode = TABLE;
+            return;
+        }
         crc_mbed_config_t config;
         config.polynomial  = polynomial;
         config.width       = width;
@@ -510,10 +521,14 @@ class MbedCRC {
             return;
         }
 #endif
+
         switch (polynomial) {
             case POLY_32BIT_ANSI:
                 _crc_table = (uint32_t *)Table_CRC_32bit_ANSI;
                 break;
+            case POLY_32BIT_REV_ANSI:
+                _crc_table = (uint32_t *)Table_CRC_32bit_Rev_ANSI;
+                break;
             case POLY_8BIT_CCITT:
                 _crc_table = (uint32_t *)Table_CRC_8bit_CCITT;
                 break;

UNITTESTS/stubs/Mutex_stub.cpp

@@ -91,7 +91,7 @@ qspi_status_t QSPI::set_frequency(int hz)
     return ret_status;
 }
 
-qspi_status_t QSPI::read(unsigned int address, char *rx_buffer, size_t *rx_length)
+qspi_status_t QSPI::read(int address, char *rx_buffer, size_t *rx_length)
 {
     qspi_status_t ret_status = QSPI_STATUS_ERROR;
 
@@ -115,7 +115,7 @@ qspi_status_t QSPI::read(unsigned int address, char *rx_buffer, size_t *rx_lengt
     return ret_status;
 }
 
-qspi_status_t QSPI::write(unsigned int address, const char *tx_buffer, size_t *tx_length)
+qspi_status_t QSPI::write(int address, const char *tx_buffer, size_t *tx_length)
 {
     qspi_status_t ret_status = QSPI_STATUS_ERROR;
 
@@ -139,7 +139,7 @@ qspi_status_t QSPI::write(unsigned int address, const char *tx_buffer, size_t *t
     return ret_status;
 }
 
-qspi_status_t QSPI::read(unsigned int instruction, unsigned int alt, unsigned int address, char *rx_buffer, size_t *rx_length)
+qspi_status_t QSPI::read(int instruction, int alt, int address, char *rx_buffer, size_t *rx_length)
 {
     qspi_status_t ret_status = QSPI_STATUS_ERROR;
 
@@ -163,7 +163,7 @@ qspi_status_t QSPI::read(unsigned int instruction, unsigned int alt, unsigned in
     return ret_status;
 }
 
-qspi_status_t QSPI::write(unsigned int instruction, unsigned int alt, unsigned int address, const char *tx_buffer, size_t *tx_length)
+qspi_status_t QSPI::write(int instruction, int alt, int address, const char *tx_buffer, size_t *tx_length)
 {
     qspi_status_t ret_status = QSPI_STATUS_ERROR;
 
@@ -187,7 +187,7 @@ qspi_status_t QSPI::write(unsigned int instruction, unsigned int alt, unsigned i
     return ret_status;
 }
 
-qspi_status_t QSPI::command_transfer(unsigned int instruction, int address, const char *tx_buffer, size_t tx_length, const char *rx_buffer, size_t rx_length)
+qspi_status_t QSPI::command_transfer(int instruction, int address, const char *tx_buffer, size_t tx_length, const char *rx_buffer, size_t rx_length)
 {
     qspi_status_t ret_status = QSPI_STATUS_ERROR;
 

drivers/MbedCRC.cpp

@@ -44,19 +44,27 @@ namespace mbed {
  *
  * #include "mbed.h"
  *
+ * #define CMD_WRITE 0x02
+ * #define CMD_READ  0x03
+ * #define ADDRESS   0x1000
+ *
  * // hardware ssel (where applicable)
- * QSPI qspi_device(QSPI_PIN_IO0, QSPI_PIN_IO1, QSPI_PIN_IO2, QSPI_PIN_IO3, QSPI_PIN_SCK, QSPI_PIN_CSN); // io0, io1, io2, io3, sclk, ssel
+ * QSPI qspi_device(QSPI_FLASH1_IO0, QSPI_FLASH1_IO1, QSPI_FLASH1_IO2, QSPI_FLASH1_IO3, QSPI_FLASH1_SCK, QSPI_FLASH1_CSN); // io0, io1, io2, io3, sclk, ssel
  *
  *
  * int main() {
  *     char tx_buf[] = { 0x11, 0x22, 0x33, 0x44 };
  *     char rx_buf[4];
  *     int buf_len = sizeof(tx_buf);
  *
- *     int result = qspi_device.write( 0x12 , 0x100000 , 0 , tx_buf, &buf_len );
- *     if( !result ) printf("Write failed");
- *     int result = qspi_device.read( 0x13 , 0x100000 , 0 , rx_buf, &buf_len );
- *     if( !result ) printf("Read failed");
+ *     qspi_status_t result = qspi_device.write(CMD_WRITE, 0, ADDRESS, tx_buf, &buf_len);
+ *     if (result != QSPI_STATUS_OK) {
+ *        printf("Write failed");
+ *     }
+ *     result = qspi_device.read(CMD_READ, 0, ADDRESS, rx_buf, &buf_len);
+ *     if (result != QSPI_STATUS_OK) {
+ *        printf("Read failed");
+ *     }
  *
  * }
  * @endcode
@@ -118,7 +126,7 @@ class QSPI : private NonCopyable<QSPI> {
      *  @returns
      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
      */
-    qspi_status_t read(unsigned int address, char *rx_buffer, size_t *rx_length);
+    qspi_status_t read(int address, char *rx_buffer, size_t *rx_length);
 
     /** Write to QSPI peripheral using custom write instruction
      *
@@ -129,38 +137,38 @@ class QSPI : private NonCopyable<QSPI> {
      *  @returns
      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
      */
-    qspi_status_t write(unsigned int address, const char *tx_buffer, size_t *tx_length);
+    qspi_status_t write(int address, const char *tx_buffer, size_t *tx_length);
 
     /** Read from QSPI peripheral using custom read instruction, alt values
      *
      *  @param instruction Instruction value to be used in instruction phase
-     *  @param alt Alt value to be used in instruction phase
+     *  @param alt Alt value to be used in Alternate-byte phase. Use -1 for ignoring Alternate-byte phase
      *  @param address Address to be accessed in QSPI peripheral
      *  @param rx_buffer Buffer for data to be read from the peripheral
      *  @param rx_length Pointer to a variable containing the length of rx_buffer, and on return this variable will be updated with the actual number of bytes read
      *
      *  @returns
      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
      */
-    qspi_status_t read(unsigned int instruction, unsigned int alt, unsigned int address, char *rx_buffer, size_t *rx_length);
+    qspi_status_t read(int instruction, int alt, int address, char *rx_buffer, size_t *rx_length);
 
     /** Write to QSPI peripheral using custom write instruction, alt values
      *
      *  @param instruction Instruction value to be used in instruction phase
-     *  @param alt Alt value to be used in instruction phase
+     *  @param alt Alt value to be used in Alternate-byte phase. Use -1 for ignoring Alternate-byte phase
      *  @param address Address to be accessed in QSPI peripheral
      *  @param tx_buffer Buffer containing data to be sent to peripheral
      *  @param tx_length Pointer to a variable containing the length of data to be transmitted, and on return this variable will be updated with the actual number of bytes written
      *
      *  @returns
      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
      */
-    qspi_status_t write(unsigned int instruction, unsigned int alt, unsigned int address, const char *tx_buffer, size_t *tx_length);
+    qspi_status_t write(int instruction, int alt, int address, const char *tx_buffer, size_t *tx_length);
 
     /** Perform a transaction to write to an address(a control register) and get the status results
      *
      *  @param instruction Instruction value to be used in instruction phase
-     *  @param address Some instruction might require address. Use -1 for ignoring the address value
+     *  @param address Some instruction might require address. Use -1 if no address
      *  @param tx_buffer Buffer containing data to be sent to peripheral
      *  @param tx_length Pointer to a variable containing the length of data to be transmitted, and on return this variable will be updated with the actual number of bytes written
      *  @param rx_buffer Buffer for data to be read from the peripheral
@@ -169,7 +177,7 @@ class QSPI : private NonCopyable<QSPI> {
      *  @returns
      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
      */
-    qspi_status_t command_transfer(unsigned int instruction, int address, const char *tx_buffer, size_t tx_length, const char *rx_buffer, size_t rx_length);
+    qspi_status_t command_transfer(int instruction, int address, const char *tx_buffer, size_t tx_length, const char *rx_buffer, size_t rx_length);
 
 protected:
     /** Acquire exclusive access to this SPI bus

drivers/MbedCRC.h

@@ -108,12 +108,48 @@ extern const uint16_t Table_CRC_16bit_IBM[MBED_CRC_TABLE_SIZE] = {
     0x220,  0x8225, 0x822f, 0x22a,  0x823b, 0x23e,  0x234,  0x8231, 0x8213, 0x216,  0x21c,  0x8219
 };
 
-extern const uint32_t Table_CRC_32bit_ANSI[MBED_OPTIMIZED_CRC_TABLE_SIZE] = {
+extern const uint32_t Table_CRC_32bit_ANSI[MBED_CRC_TABLE_SIZE] = {
+    0x0,        0x4c11db7,  0x9823b6e,  0xd4326d9,  0x130476dc, 0x17c56b6b, 0x1a864db2, 0x1e475005,
+    0x2608edb8, 0x22c9f00f, 0x2f8ad6d6, 0x2b4bcb61, 0x350c9b64, 0x31cd86d3, 0x3c8ea00a, 0x384fbdbd,
+    0x4c11db70, 0x48d0c6c7, 0x4593e01e, 0x4152fda9, 0x5f15adac, 0x5bd4b01b, 0x569796c2, 0x52568b75,
+    0x6a1936c8, 0x6ed82b7f, 0x639b0da6, 0x675a1011, 0x791d4014, 0x7ddc5da3, 0x709f7b7a, 0x745e66cd,
+    0x9823b6e0, 0x9ce2ab57, 0x91a18d8e, 0x95609039, 0x8b27c03c, 0x8fe6dd8b, 0x82a5fb52, 0x8664e6e5,
+    0xbe2b5b58, 0xbaea46ef, 0xb7a96036, 0xb3687d81, 0xad2f2d84, 0xa9ee3033, 0xa4ad16ea, 0xa06c0b5d,
+    0xd4326d90, 0xd0f37027, 0xddb056fe, 0xd9714b49, 0xc7361b4c, 0xc3f706fb, 0xceb42022, 0xca753d95,
+    0xf23a8028, 0xf6fb9d9f, 0xfbb8bb46, 0xff79a6f1, 0xe13ef6f4, 0xe5ffeb43, 0xe8bccd9a, 0xec7dd02d,
+    0x34867077, 0x30476dc0, 0x3d044b19, 0x39c556ae, 0x278206ab, 0x23431b1c, 0x2e003dc5, 0x2ac12072,
+    0x128e9dcf, 0x164f8078, 0x1b0ca6a1, 0x1fcdbb16, 0x18aeb13,  0x54bf6a4,  0x808d07d,  0xcc9cdca,
+    0x7897ab07, 0x7c56b6b0, 0x71159069, 0x75d48dde, 0x6b93dddb, 0x6f52c06c, 0x6211e6b5, 0x66d0fb02,
+    0x5e9f46bf, 0x5a5e5b08, 0x571d7dd1, 0x53dc6066, 0x4d9b3063, 0x495a2dd4, 0x44190b0d, 0x40d816ba,
+    0xaca5c697, 0xa864db20, 0xa527fdf9, 0xa1e6e04e, 0xbfa1b04b, 0xbb60adfc, 0xb6238b25, 0xb2e29692,
+    0x8aad2b2f, 0x8e6c3698, 0x832f1041, 0x87ee0df6, 0x99a95df3, 0x9d684044, 0x902b669d, 0x94ea7b2a,
+    0xe0b41de7, 0xe4750050, 0xe9362689, 0xedf73b3e, 0xf3b06b3b, 0xf771768c, 0xfa325055, 0xfef34de2,
+    0xc6bcf05f, 0xc27dede8, 0xcf3ecb31, 0xcbffd686, 0xd5b88683, 0xd1799b34, 0xdc3abded, 0xd8fba05a,
+    0x690ce0ee, 0x6dcdfd59, 0x608edb80, 0x644fc637, 0x7a089632, 0x7ec98b85, 0x738aad5c, 0x774bb0eb,
+    0x4f040d56, 0x4bc510e1, 0x46863638, 0x42472b8f, 0x5c007b8a, 0x58c1663d, 0x558240e4, 0x51435d53,
+    0x251d3b9e, 0x21dc2629, 0x2c9f00f0, 0x285e1d47, 0x36194d42, 0x32d850f5, 0x3f9b762c, 0x3b5a6b9b,
+    0x315d626,  0x7d4cb91,  0xa97ed48,  0xe56f0ff,  0x1011a0fa, 0x14d0bd4d, 0x19939b94, 0x1d528623,
+    0xf12f560e, 0xf5ee4bb9, 0xf8ad6d60, 0xfc6c70d7, 0xe22b20d2, 0xe6ea3d65, 0xeba91bbc, 0xef68060b,
+    0xd727bbb6, 0xd3e6a601, 0xdea580d8, 0xda649d6f, 0xc423cd6a, 0xc0e2d0dd, 0xcda1f604, 0xc960ebb3,
+    0xbd3e8d7e, 0xb9ff90c9, 0xb4bcb610, 0xb07daba7, 0xae3afba2, 0xaafbe615, 0xa7b8c0cc, 0xa379dd7b,
+    0x9b3660c6, 0x9ff77d71, 0x92b45ba8, 0x9675461f, 0x8832161a, 0x8cf30bad, 0x81b02d74, 0x857130c3,
+    0x5d8a9099, 0x594b8d2e, 0x5408abf7, 0x50c9b640, 0x4e8ee645, 0x4a4ffbf2, 0x470cdd2b, 0x43cdc09c,
+    0x7b827d21, 0x7f436096, 0x7200464f, 0x76c15bf8, 0x68860bfd, 0x6c47164a, 0x61043093, 0x65c52d24,
+    0x119b4be9, 0x155a565e, 0x18197087, 0x1cd86d30, 0x29f3d35,  0x65e2082,  0xb1d065b,  0xfdc1bec,
+    0x3793a651, 0x3352bbe6, 0x3e119d3f, 0x3ad08088, 0x2497d08d, 0x2056cd3a, 0x2d15ebe3, 0x29d4f654,
+    0xc5a92679, 0xc1683bce, 0xcc2b1d17, 0xc8ea00a0, 0xd6ad50a5, 0xd26c4d12, 0xdf2f6bcb, 0xdbee767c,
+    0xe3a1cbc1, 0xe760d676, 0xea23f0af, 0xeee2ed18, 0xf0a5bd1d, 0xf464a0aa, 0xf9278673, 0xfde69bc4,
+    0x89b8fd09, 0x8d79e0be, 0x803ac667, 0x84fbdbd0, 0x9abc8bd5, 0x9e7d9662, 0x933eb0bb, 0x97ffad0c,
+    0xafb010b1, 0xab710d06, 0xa6322bdf, 0xa2f33668, 0xbcb4666d, 0xb8757bda, 0xb5365d03, 0xb1f740b4
+};
+
+extern const uint32_t Table_CRC_32bit_Rev_ANSI[MBED_OPTIMIZED_CRC_TABLE_SIZE] = {
     0x00000000, 0x1db71064, 0x3b6e20c8, 0x26d930ac,
     0x76dc4190, 0x6b6b51f4, 0x4db26158, 0x5005713c,
     0xedb88320, 0xf00f9344, 0xd6d6a3e8, 0xcb61b38c,
     0x9b64c2b0, 0x86d3d2d4, 0xa00ae278, 0xbdbdf21c
 };
 
+
 /** @}*/
 } // namespace mbed

drivers/QSPI.cpp

@@ -30,7 +30,8 @@ extern const uint8_t Table_CRC_7Bit_SD[MBED_CRC_TABLE_SIZE];
 extern const uint8_t Table_CRC_8bit_CCITT[MBED_CRC_TABLE_SIZE];
 extern const uint16_t Table_CRC_16bit_CCITT[MBED_CRC_TABLE_SIZE];
 extern const uint16_t Table_CRC_16bit_IBM[MBED_CRC_TABLE_SIZE];
-extern const uint32_t Table_CRC_32bit_ANSI[MBED_OPTIMIZED_CRC_TABLE_SIZE];
+extern const uint32_t Table_CRC_32bit_ANSI[MBED_CRC_TABLE_SIZE];
+extern const uint32_t Table_CRC_32bit_Rev_ANSI[MBED_OPTIMIZED_CRC_TABLE_SIZE];
 
 /** @}*/
 } // namespace mbed

drivers/QSPI.h

@@ -1,5 +1,12 @@
 # Change Log
 
+## [v4.6.3](https://github.com/ARMmbed/mbed-coap/releases/tag/v4.6.3) 
+
+ - Bug fix: Remove timed out blockwise message from resend queue. If blockwise message was timed out message was still kept in the resend queue which causes unnecessary reconnections on client side.
+ - Documentation: Document all the available macros.
+
+-[Full Changelog](https://github.com/ARMmbed/mbed-coap/compare/v4.6.2...v4.6.3)
+
 ## [v4.6.2](https://github.com/ARMmbed/mbed-coap/releases/tag/v4.6.2) 
 
 Do not clear block2 in subsequent block request.