net: Add Qcom WWAN control driver

The MHI WWWAN control driver allows MHI QCOM-based modems to expose
different modem control protocols/ports via the WWAN framework, so that
userspace modem tools or daemon (e.g. ModemManager) can control WWAN
config and state (APN config, SMS, provider selection...). A QCOM-based
modem can expose one or several of the following protocols:
- AT: Well known AT commands interactive protocol (microcom, minicom...)
- MBIM: Mobile Broadband Interface Model (libmbim, mbimcli)
- QMI: QCOM MSM/Modem Interface (libqmi, qmicli)
- QCDM: QCOM Modem diagnostic interface (libqcdm)
- FIREHOSE: XML-based protocol for Modem firmware management
        (qmi-firmware-update)

Note that this patch is mostly a rework of the earlier MHI UCI
tentative that was a generic interface for accessing MHI bus from
userspace. As suggested, this new version is WWAN specific and is
dedicated to only expose channels used for controlling a modem, and
for which related opensource userpace support exist.

Signed-off-by: Loic Poulain <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

Author: Loic Poulain

drivers/net/wwan/Kconfig

@@ -20,4 +20,18 @@ config WWAN_CORE
 	  To compile this driver as a module, choose M here: the module will be
 	  called wwan.
 
+config MHI_WWAN_CTRL
+	tristate "MHI WWAN control driver for QCOM-based PCIe modems"
+	select WWAN_CORE
+	depends on MHI_BUS
+	help
+	  MHI WWAN CTRL allows QCOM-based PCIe modems to expose different modem
+	  control protocols/ports to userspace, including AT, MBIM, QMI, DIAG
+	  and FIREHOSE. These protocols can be accessed directly from userspace
+	  (e.g. AT commands) or via libraries/tools (e.g. libmbim, libqmi,
+	  libqcdm...).
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called mhi_wwan_ctrl.
+
 endif # WWAN

drivers/net/wwan/Makefile

@@ -5,3 +5,5 @@
 
 obj-$(CONFIG_WWAN_CORE) += wwan.o
 wwan-objs += wwan_core.o
+
+obj-$(CONFIG_MHI_WWAN_CTRL) += mhi_wwan_ctrl.o

drivers/net/wwan/mhi_wwan_ctrl.c

@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* Copyright (c) 2021, Linaro Ltd <[email protected]> */
+#include <linux/kernel.h>
+#include <linux/mhi.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/wwan.h>
+
+/* MHI wwan flags */
+#define MHI_WWAN_DL_CAP		BIT(0)
+#define MHI_WWAN_UL_CAP		BIT(1)
+#define MHI_WWAN_RX_REFILL	BIT(2)
+
+#define MHI_WWAN_MAX_MTU	0x8000
+
+struct mhi_wwan_dev {
+	/* Lower level is a mhi dev, upper level is a wwan port */
+	struct mhi_device *mhi_dev;
+	struct wwan_port *wwan_port;
+
+	/* State and capabilities */
+	unsigned long flags;
+	size_t mtu;
+
+	/* Protect against concurrent TX and TX-completion (bh) */
+	spinlock_t tx_lock;
+
+	/* Protect RX budget and rx_refill scheduling */
+	spinlock_t rx_lock;
+	struct work_struct rx_refill;
+
+	/* RX budget is initially set to the size of the MHI RX queue and is
+	 * used to limit the number of allocated and queued packets. It is
+	 * decremented on data queueing and incremented on data release.
+	 */
+	unsigned int rx_budget;
+};
+
+/* Increment RX budget and schedule RX refill if necessary */
+static void mhi_wwan_rx_budget_inc(struct mhi_wwan_dev *mhiwwan)
+{
+	spin_lock(&mhiwwan->rx_lock);
+
+	mhiwwan->rx_budget++;
+
+	if (test_bit(MHI_WWAN_RX_REFILL, &mhiwwan->flags))
+		schedule_work(&mhiwwan->rx_refill);
+
+	spin_unlock(&mhiwwan->rx_lock);
+}
+
+/* Decrement RX budget if non-zero and return true on success */
+static bool mhi_wwan_rx_budget_dec(struct mhi_wwan_dev *mhiwwan)
+{
+	bool ret = false;
+
+	spin_lock(&mhiwwan->rx_lock);
+
+	if (mhiwwan->rx_budget)
+		mhiwwan->rx_budget--;
+
+	if (mhiwwan->rx_budget && test_bit(MHI_WWAN_RX_REFILL, &mhiwwan->flags))
+		ret = true;
+
+	spin_unlock(&mhiwwan->rx_lock);
+
+	return ret;
+}
+
+static void __mhi_skb_destructor(struct sk_buff *skb)
+{
+	/* RX buffer has been consumed, increase the allowed budget */
+	mhi_wwan_rx_budget_inc(skb_shinfo(skb)->destructor_arg);
+}
+
+static void mhi_wwan_ctrl_refill_work(struct work_struct *work)
+{
+	struct mhi_wwan_dev *mhiwwan = container_of(work, struct mhi_wwan_dev, rx_refill);
+	struct mhi_device *mhi_dev = mhiwwan->mhi_dev;
+
+	while (mhi_wwan_rx_budget_dec(mhiwwan)) {
+		struct sk_buff *skb;
+
+		skb = alloc_skb(mhiwwan->mtu, GFP_KERNEL);
+		if (!skb) {
+			mhi_wwan_rx_budget_inc(mhiwwan);
+			break;
+		}
+
+		/* To prevent unlimited buffer allocation if nothing consumes
+		 * the RX buffers (passed to WWAN core), track their lifespan
+		 * to not allocate more than allowed budget.
+		 */
+		skb->destructor = __mhi_skb_destructor;
+		skb_shinfo(skb)->destructor_arg = mhiwwan;
+
+		if (mhi_queue_skb(mhi_dev, DMA_FROM_DEVICE, skb, mhiwwan->mtu, MHI_EOT)) {
+			dev_err(&mhi_dev->dev, "Failed to queue buffer\n");
+			kfree_skb(skb);
+			break;
+		}
+	}
+}
+
+static int mhi_wwan_ctrl_start(struct wwan_port *port)
+{
+	struct mhi_wwan_dev *mhiwwan = wwan_port_get_drvdata(port);
+	int ret;
+
+	/* Start mhi device's channel(s) */
+	ret = mhi_prepare_for_transfer(mhiwwan->mhi_dev);
+	if (ret)
+		return ret;
+
+	/* Don't allocate more buffers than MHI channel queue size */
+	mhiwwan->rx_budget = mhi_get_free_desc_count(mhiwwan->mhi_dev, DMA_FROM_DEVICE);
+
+	/* Add buffers to the MHI inbound queue */
+	if (test_bit(MHI_WWAN_DL_CAP, &mhiwwan->flags)) {
+		set_bit(MHI_WWAN_RX_REFILL, &mhiwwan->flags);
+		mhi_wwan_ctrl_refill_work(&mhiwwan->rx_refill);
+	}
+
+	return 0;
+}
+
+static void mhi_wwan_ctrl_stop(struct wwan_port *port)
+{
+	struct mhi_wwan_dev *mhiwwan = wwan_port_get_drvdata(port);
+
+	spin_lock(&mhiwwan->rx_lock);
+	clear_bit(MHI_WWAN_RX_REFILL, &mhiwwan->flags);
+	spin_unlock(&mhiwwan->rx_lock);
+
+	cancel_work_sync(&mhiwwan->rx_refill);
+
+	mhi_unprepare_from_transfer(mhiwwan->mhi_dev);
+}
+
+static int mhi_wwan_ctrl_tx(struct wwan_port *port, struct sk_buff *skb)
+{
+	struct mhi_wwan_dev *mhiwwan = wwan_port_get_drvdata(port);
+	int ret;
+
+	if (skb->len > mhiwwan->mtu)
+		return -EMSGSIZE;
+
+	if (!test_bit(MHI_WWAN_UL_CAP, &mhiwwan->flags))
+		return -EOPNOTSUPP;
+
+	/* Queue the packet for MHI transfer and check fullness of the queue */
+	spin_lock_bh(&mhiwwan->tx_lock);
+	ret = mhi_queue_skb(mhiwwan->mhi_dev, DMA_TO_DEVICE, skb, skb->len, MHI_EOT);
+	if (mhi_queue_is_full(mhiwwan->mhi_dev, DMA_TO_DEVICE))
+		wwan_port_txoff(port);
+	spin_unlock_bh(&mhiwwan->tx_lock);
+
+	return ret;
+}
+
+static const struct wwan_port_ops wwan_pops = {
+	.start = mhi_wwan_ctrl_start,
+	.stop = mhi_wwan_ctrl_stop,
+	.tx = mhi_wwan_ctrl_tx,
+};
+
+static void mhi_ul_xfer_cb(struct mhi_device *mhi_dev,
+			   struct mhi_result *mhi_result)
+{
+	struct mhi_wwan_dev *mhiwwan = dev_get_drvdata(&mhi_dev->dev);
+	struct wwan_port *port = mhiwwan->wwan_port;
+	struct sk_buff *skb = mhi_result->buf_addr;
+
+	dev_dbg(&mhi_dev->dev, "%s: status: %d xfer_len: %zu\n", __func__,
+		mhi_result->transaction_status, mhi_result->bytes_xferd);
+
+	/* MHI core has done with the buffer, release it */
+	consume_skb(skb);
+
+	/* There is likely new slot available in the MHI queue, re-allow TX */
+	spin_lock_bh(&mhiwwan->tx_lock);
+	if (!mhi_queue_is_full(mhiwwan->mhi_dev, DMA_TO_DEVICE))
+		wwan_port_txon(port);
+	spin_unlock_bh(&mhiwwan->tx_lock);
+}
+
+static void mhi_dl_xfer_cb(struct mhi_device *mhi_dev,
+			   struct mhi_result *mhi_result)
+{
+	struct mhi_wwan_dev *mhiwwan = dev_get_drvdata(&mhi_dev->dev);
+	struct wwan_port *port = mhiwwan->wwan_port;
+	struct sk_buff *skb = mhi_result->buf_addr;
+
+	dev_dbg(&mhi_dev->dev, "%s: status: %d receive_len: %zu\n", __func__,
+		mhi_result->transaction_status, mhi_result->bytes_xferd);
+
+	if (mhi_result->transaction_status &&
+	    mhi_result->transaction_status != -EOVERFLOW) {
+		kfree_skb(skb);
+		return;
+	}
+
+	/* MHI core does not update skb->len, do it before forward */
+	skb_put(skb, mhi_result->bytes_xferd);
+	wwan_port_rx(port, skb);
+
+	/* Do not increment rx budget nor refill RX buffers now, wait for the
+	 * buffer to be consumed. Done from __mhi_skb_destructor().
+	 */
+}
+
+static int mhi_wwan_ctrl_probe(struct mhi_device *mhi_dev,
+			       const struct mhi_device_id *id)
+{
+	struct mhi_controller *cntrl = mhi_dev->mhi_cntrl;
+	struct mhi_wwan_dev *mhiwwan;
+	struct wwan_port *port;
+
+	mhiwwan = kzalloc(sizeof(*mhiwwan), GFP_KERNEL);
+	if (!mhiwwan)
+		return -ENOMEM;
+
+	mhiwwan->mhi_dev = mhi_dev;
+	mhiwwan->mtu = MHI_WWAN_MAX_MTU;
+	INIT_WORK(&mhiwwan->rx_refill, mhi_wwan_ctrl_refill_work);
+	spin_lock_init(&mhiwwan->tx_lock);
+	spin_lock_init(&mhiwwan->rx_lock);
+
+	if (mhi_dev->dl_chan)
+		set_bit(MHI_WWAN_DL_CAP, &mhiwwan->flags);
+	if (mhi_dev->ul_chan)
+		set_bit(MHI_WWAN_UL_CAP, &mhiwwan->flags);
+
+	dev_set_drvdata(&mhi_dev->dev, mhiwwan);
+
+	/* Register as a wwan port, id->driver_data contains wwan port type */
+	port = wwan_create_port(&cntrl->mhi_dev->dev, id->driver_data,
+				&wwan_pops, mhiwwan);
+	if (IS_ERR(port)) {
+		kfree(mhiwwan);
+		return PTR_ERR(port);
+	}
+
+	mhiwwan->wwan_port = port;
+
+	return 0;
+};
+
+static void mhi_wwan_ctrl_remove(struct mhi_device *mhi_dev)
+{
+	struct mhi_wwan_dev *mhiwwan = dev_get_drvdata(&mhi_dev->dev);
+
+	wwan_remove_port(mhiwwan->wwan_port);
+	kfree(mhiwwan);
+}
+
+static const struct mhi_device_id mhi_wwan_ctrl_match_table[] = {
+	{ .chan = "DUN", .driver_data = WWAN_PORT_AT },
+	{ .chan = "MBIM", .driver_data = WWAN_PORT_MBIM },
+	{ .chan = "QMI", .driver_data = WWAN_PORT_QMI },
+	{ .chan = "DIAG", .driver_data = WWAN_PORT_QCDM },
+	{ .chan = "FIREHOSE", .driver_data = WWAN_PORT_FIREHOSE },
+	{},
+};
+MODULE_DEVICE_TABLE(mhi, mhi_wwan_ctrl_match_table);
+
+static struct mhi_driver mhi_wwan_ctrl_driver = {
+	.id_table = mhi_wwan_ctrl_match_table,
+	.remove = mhi_wwan_ctrl_remove,
+	.probe = mhi_wwan_ctrl_probe,
+	.ul_xfer_cb = mhi_ul_xfer_cb,
+	.dl_xfer_cb = mhi_dl_xfer_cb,
+	.driver = {
+		.name = "mhi_wwan_ctrl",
+	},
+};
+
+module_mhi_driver(mhi_wwan_ctrl_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("MHI WWAN CTRL Driver");
+MODULE_AUTHOR("Loic Poulain <[email protected]>");