Merge tag 'v4.13-rc6' into asoc-msm8916

Linux 4.13-rc6

Author: broonie

Documentation/admin-guide/pm/cpufreq.rst

@@ -237,6 +237,14 @@ are the following:
 	This attribute is not present if the scaling driver in use does not
 	support it.
 
+``cpuinfo_cur_freq``
+	Current frequency of the CPUs belonging to this policy as obtained from
+	the hardware (in KHz).
+
+	This is expected to be the frequency the hardware actually runs at.
+	If that frequency cannot be determined, this attribute should not
+	be present.
+
 ``cpuinfo_max_freq``
 	Maximum possible operating frequency the CPUs belonging to this policy
 	can run at (in kHz).

Documentation/device-mapper/dm-raid.txt

@@ -343,3 +343,4 @@ Version History
 1.11.0  Fix table line argument order
 	(wrong raid10_copies/raid10_format sequence)
 1.11.1  Add raid4/5/6 journal write-back support via journal_mode option
+1.12.1  fix for MD deadlock between mddev_suspend() and md_write_start() available

Documentation/devicetree/bindings/ata/sata_rcar.txt

@@ -1,22 +1,30 @@
 * Renesas R-Car SATA
 
 Required properties:
-- compatible		: should contain one of the following:
+- compatible		: should contain one or more of the following:
 			  - "renesas,sata-r8a7779" for R-Car H1
-			    ("renesas,rcar-sata" is deprecated)
 			  - "renesas,sata-r8a7790-es1" for R-Car H2 ES1
 			  - "renesas,sata-r8a7790" for R-Car H2 other than ES1
 			  - "renesas,sata-r8a7791" for R-Car M2-W
 			  - "renesas,sata-r8a7793" for R-Car M2-N
 			  - "renesas,sata-r8a7795" for R-Car H3
+			  - "renesas,rcar-gen2-sata" for a generic R-Car Gen2 compatible device
+			  - "renesas,rcar-gen3-sata" for a generic R-Car Gen3 compatible device
+			  - "renesas,rcar-sata" is deprecated
+
+			  When compatible with the generic version nodes
+			  must list the SoC-specific version corresponding
+			  to the platform first followed by the generic
+			  version.
+
 - reg			: address and length of the SATA registers;
 - interrupts		: must consist of one interrupt specifier.
 - clocks		: must contain a reference to the functional clock.
 
 Example:
 
 sata0: sata@ee300000 {
-	compatible = "renesas,sata-r8a7791";
+	compatible = "renesas,sata-r8a7791", "renesas,rcar-gen2-sata";
 	reg = <0 0xee300000 0 0x2000>;
 	interrupt-parent = <&gic>;
 	interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>;

Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt

@@ -8,7 +8,6 @@ Required properties:
 
 Optional properties:
 - clocks: Reference to the crypto engine clock.
-- dma-mask: The address mask limitation. Defaults to 64.
 
 Example:
 
@@ -24,6 +23,5 @@ Example:
 		interrupt-names = "mem", "ring0", "ring1", "ring2", "ring3",
 				  "eip";
 		clocks = <&cpm_syscon0 1 26>;
-		dma-mask = <0xff 0xffffffff>;
 		status = "disabled";
 	};

Documentation/devicetree/bindings/gpio/gpio-exar.txt

@@ -0,0 +1,5 @@
+Exportable MPIO interface of Exar UART chips
+
+Required properties of the device:
+ - exar,first-pin: first exportable pins (0..15)
+ - ngpios: number of exportable pins (1..16)

Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt

@@ -40,7 +40,7 @@ Optional properties:
 Example for a Mali-T760:
 
 gpu@ffa30000 {
-	compatible = "rockchip,rk3288-mali", "arm,mali-t760", "arm,mali-midgard";
+	compatible = "rockchip,rk3288-mali", "arm,mali-t760";
 	reg = <0xffa30000 0x10000>;
 	interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,

Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt

@@ -78,7 +78,6 @@ Example:
 	};
 
 	dwmmc0@12200000 {
-		num-slots = <1>;
 		cap-mmc-highspeed;
 		cap-sd-highspeed;
 		broken-cd;

Documentation/devicetree/bindings/mmc/img-dw-mshc.txt

@@ -24,6 +24,5 @@ Example:
 
 		fifo-depth = <0x20>;
 		bus-width = <4>;
-		num-slots = <1>;
 		disable-wp;
 	};

Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt

@@ -36,7 +36,6 @@ Example:
 
 	/* Board portion */
 	dwmmc0@fcd03000 {
-		num-slots = <1>;
 		vmmc-supply = <&ldo12>;
 		fifo-depth = <0x100>;
 		pinctrl-names = "default";
@@ -52,7 +51,6 @@ Example:
 
 	dwmmc_1: dwmmc1@f723e000 {
 		compatible = "hisilicon,hi6220-dw-mshc";
-		num-slots = <0x1>;
 		bus-width = <0x4>;
 		disable-wp;
 		cap-sd-highspeed;

Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt

@@ -12,12 +12,12 @@ Required Properties:
 * #address-cells: should be 1.
 * #size-cells: should be 0.
 
-# Slots: The slot specific information are contained within child-nodes with
-  each child-node representing a supported slot. There should be atleast one
-  child node representing a card slot. The name of the child node representing
-  the slot is recommended to be slot@n where n is the unique number of the slot
-  connected to the controller. The following are optional properties which
-  can be included in the slot child node.
+# Slots (DEPRECATED): The slot specific information are contained within
+  child-nodes with each child-node representing a supported slot. There should
+  be atleast one child node representing a card slot. The name of the child node
+  representing the slot is recommended to be slot@n where n is the unique number
+  of the slot connected to the controller. The following are optional properties
+  which can be included in the slot child node.
 
 	* reg: specifies the physical slot number. The valid values of this
 	  property is 0 to (num-slots -1), where num-slots is the value
@@ -63,7 +63,7 @@ Optional properties:
   clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default.
 	  (Use the "max-frequency" instead of "clock-freq-min-max".)
 
-* num-slots: specifies the number of slots supported by the controller.
+* num-slots (DEPRECATED): specifies the number of slots supported by the controller.
   The number of physical slots actually used could be equal or less than the
   value specified by num-slots. If this property is not specified, the value
   of num-slot property is assumed to be 1.
@@ -124,7 +124,6 @@ board specific portions as listed below.
 	dwmmc0@12200000 {
 		clock-frequency = <400000000>;
 		clock-freq-min-max = <400000 200000000>;
-		num-slots = <1>;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
@@ -139,7 +138,6 @@ board specific portions as listed below.
 	dwmmc0@12200000 {
 		clock-frequency = <400000000>;
 		clock-freq-min-max = <400000 200000000>;
-		num-slots = <1>;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;

Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt

@@ -25,7 +25,6 @@ Example:
 		clock-frequency = <50000000>;
 		clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
 		clock-names = "biu", "ciu";
-		num-slots = <1>;
 		max-frequency = <50000000>;
 		cap-sdio-irq;
 		cap-sd-highspeed;

Documentation/devicetree/bindings/net/brcm,amac.txt

@@ -11,6 +11,7 @@ Required properties:
  - reg-names:	Names of the registers.
 		"amac_base":	Address and length of the GMAC registers
 		"idm_base":	Address and length of the GMAC IDM registers
+				(required for NSP and Northstar2)
 		"nicpm_base":	Address and length of the NIC Port Manager
 				registers (required for Northstar2)
  - interrupts:	Interrupt number

Documentation/devicetree/bindings/net/brcm,bgmac-nsp.txt

@@ -4,7 +4,7 @@ Required properties:
 - compatible: Should be one of the following.
   - "rockchip,rk3066a-efuse" - for RK3066a SoCs.
   - "rockchip,rk3188-efuse" - for RK3188 SoCs.
-  - "rockchip,rk322x-efuse" - for RK322x SoCs.
+  - "rockchip,rk3228-efuse" - for RK3228 SoCs.
   - "rockchip,rk3288-efuse" - for RK3288 SoCs.
   - "rockchip,rk3399-efuse" - for RK3399 SoCs.
 - reg: Should contain the registers location and exact eFuse size

Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt

@@ -1,13 +1,20 @@
-* Broadcom Digital Timing Engine(DTE) based PTP clock driver
+* Broadcom Digital Timing Engine(DTE) based PTP clock
 
 Required properties:
-- compatible: should be "brcm,ptp-dte"
+- compatible: should contain the core compatibility string
+              and the SoC compatibility string. The SoC
+              compatibility string is to handle SoC specific
+              hardware differences.
+              Core compatibility string:
+                 "brcm,ptp-dte"
+              SoC compatibility strings:
+                 "brcm,iproc-ptp-dte" - for iproc based SoC's
 - reg: address and length of the DTE block's NCO registers
 
 Example:
 
-ptp_dte: ptp_dte@180af650 {
-	compatible = "brcm,ptp-dte";
+ptp: ptp-dte@180af650 {
+	compatible = "brcm,iproc-ptp-dte", "brcm,ptp-dte";
 	reg = <0x180af650 0x10>;
 	status = "okay";
 };

Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt

@@ -9,7 +9,6 @@ Optional properties:
 - fsl,irda-mode : Indicate the uart supports irda mode
 - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
                   in DCE mode by default.
-- fsl,dma-size : Indicate the size of the DMA buffer and its periods
 
 Please check Documentation/devicetree/bindings/serial/serial.txt
 for the complete list of generic properties.
@@ -29,5 +28,4 @@ uart1: serial@73fbc000 {
 	interrupts = <31>;
 	uart-has-rtscts;
 	fsl,dte-mode;
-	fsl,dma-size = <1024 4>;
 };

Documentation/devicetree/bindings/serial/fsl-imx-uart.txt

@@ -27,5 +27,11 @@ You have to add the following kernel parameters in your elilo.conf:
 	Macbook Pro 17", iMac 20" :
 		video=efifb:i20
 
+Accepted options:
+
+nowc	Don't map the framebuffer write combined. This can be used
+	to workaround side-effects and slowdowns on other CPU cores
+	when large amounts of console data are written.
+
 --
 Edgar Hucek <[email protected]>

Documentation/fb/efifb.txt

@@ -459,7 +459,7 @@ pin controller?
 
 This is done by registering "ranges" of pins, which are essentially
 cross-reference tables. These are described in
-Documentation/pinctrl.txt
+Documentation/driver-api/pinctl.rst
 
 While the pin allocation is totally managed by the pinctrl subsystem,
 gpio (under gpiolib) is still maintained by gpio drivers. It may happen