arm64: dts: ti: k3-j721e-common-proc-board: add mcu cpsw nuss pinmux and phy defs

The TI J721E EVM base board has TI DP83867 PHY connected to external CPSW
NUSS Port 1 in rgmii-rxid mode.

Hence, add pinmux and Ethernet PHY configuration for TI j721e SoC MCU
Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).

Signed-off-by: Grygorii Strashko <[email protected]>
Tested-by: Murali Karicheri <[email protected]>
Tested-by: Peter Ujfalusi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

Author: grygoriyS

arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts

@@ -8,6 +8,7 @@
 #include "k3-j721e-som-p0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/net/ti-dp83867.h>
 
 / {
 	chosen {
@@ -128,6 +129,30 @@
 			J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
 		>;
 	};
+
+	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x0060, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x0064, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x006c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -429,3 +454,21 @@
 		#gpio-cells = <2>;
 	};
 };
+
+&mcu_cpsw {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+};
+
+&davinci_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&phy0>;
+};