ADS1119 Arduino Library

[ochococo]

ADS1119 Arduino Library

🌍 https://github.com/ELOWRO/ADS1119

Usage

Basic:

#include <ADS1119.h>

ADS1119 ads1 = ADS1119(byte(0B1000001));

struct ADS1119Configuration configuration;

void setup() {
  Serial.begin(9600);

  configuration.mux = ADS1119MuxConfiguration::positiveAIN0negativeAIN1;
  configuration.gain = ADS1119Configuration::Gain::one;
  configuration.dataRate  = ADS1119Configuration::DataRate::sps20;
  configuration.conversionMode = ADS1119Configuration::ConversionMode::continuous;
  configuration.voltageReference = ADS1119Configuration::VoltageReferenceSource::external;
  configuration.externalReferenceVoltage = 5.0;

  Serial.println("begin, reset");

  ads1.begin(&configuration);
  /* Config ADS1119 Amux Input as Single Ended*/
  ads1.configADCSingleEnded();
  /* Select ADS1119 Channel
  Single Ended: 4 CHANNELS => AN0, AN1, AN2, AN3
  Differential: 3 CHANNELS => AN0-AN1, AN2-AN3, AN1-AN2, 
  */
  ads1.selectChannel(0); // select AN0 (single ended input mode)
  ads1.reset();

  Serial.println("setup done");
}

void loop() {
   Serial.println(ads1.readVoltage(), 4);
}

Advanced:

#include <ADS1119.h>
#include <avr/wdt.h>

ADS1119 ads1 = ADS1119(byte(0B1000001));

struct ADS1119Configuration configuration;

void setup() {
  Serial.begin(9600);
  
  configuration.mux = ADS1119MuxConfiguration::positiveAIN0negativeAIN1;
  configuration.gain = ADS1119Configuration::Gain::one;
  configuration.dataRate  = ADS1119Configuration::DataRate::sps20;
  configuration.conversionMode = ADS1119Configuration::ConversionMode::continuous;
  configuration.voltageReference = ADS1119Configuration::VoltageReferenceSource::external;
  configuration.externalReferenceVoltage = 5.0;

  Serial.println("begin, reset");

  ads1.begin(&configuration);
  /* Config ADS1119 Amux Input as Single Ended*/
  ads1.configADCSingleEnded();
  /* Select ADS1119 Channel
  Single Ended: 4 CHANNELS => AN0, AN1, AN2, AN3
  Differential: 3 CHANNELS => AN0-AN1, AN2-AN3, AN1-AN2, 
  */
  ads1.selectChannel(0); // select AN0 (single ended input mode)
  ads1.reset();
  // Offset Calibration: VREF connected to AIN2 !!!
  // ads1.performOffsetCalibration(ADS1119MuxConfiguration::positiveAIN2negativeAGND);
  // Offset Calibration: shorting the inputs to AVDD / 2 !!!
  ads1.performOffsetCalibration(ADS1119MuxConfiguration::shortedToHalvedAVDD);
  wdt_enable(WDTO_2S);
  Serial.println("setup done");
}

void loop() {
   wdt_reset();
   Serial.println(ads1.readVoltage(configuration), 4);
   //ads.powerDown();
}

[github-actions]

A problem was found with your submission https://github.com/ELOWRO/ADS1119

❌ ERROR: The repository has no tags. You need to create a release or tag that matches the version value in the library's library.properties file.

[github-actions]

Thanks for your interest in contributing to the Arduino Library Manager index @ochococo
Please resolve the error(s) mentioned in the previous comment.

After resolving the issue, trigger this check again by doing one of the following:

• Commit the required change to the branch you submitted this pull request from.
• Comment here, mentioning @ArduinoBot in the comment.

❗ NOTE: It is not necessary to open a new pull request. ❗

More information:
https://github.com/arduino/library-registry/blob/main/README.md#if-the-problem-is-with-the-pull-request

[ochococo]

@ArduinoBot Tag is there

[github-actions]

Hello! I'm checking your submission again.

[github-actions]

Arduino Lint has suggestions for possible improvements to https://github.com/ELOWRO/ADS1119:

Linting library in ADS1119
INFO: No header file found matching library name (ADS1119_library.h). Best practices are for primary header filename to 
      match library name.                                                                                               
      See: https://arduino.github.io/arduino-cli/latest/library-specification/#libraryproperties-file-format            
      (Rule LS008)                                                                                                      
WARNING: library.properties name ADS1119 library contains spaces. Although supported, best practices is to not use      
         spaces.                                                                                                        
         See: https://arduino.github.io/arduino-cli/latest/library-specification/#libraryproperties-file-format         
         (Rule LP015)                                                                                                   
WARNING: Library name ADS1119 library contains "library". This is superfluous.                                 
         See: https://arduino.github.io/arduino-cli/latest/library-specification/#libraryproperties-file-format
         (Rule LP016)                                                                                          
WARNING: library.properties depends field item(s) Wire not found in the Library Manager index.                 
         See: https://arduino.github.io/arduino-cli/latest/library-specification/#libraryproperties-file-format
         (Rule LP048)                                                                                          
WARNING: No example sketches found. Please provide examples.                                      
         See: https://arduino.github.io/arduino-cli/latest/library-specification/#library-examples
         (Rule LD004)                                                                             

Linter results for project: 0 ERRORS, 4 WARNINGS

-------------------

[github-actions]

Your submission has now been accepted! Thanks for your contribution to the Arduino Library Manager index.

The library(s) will be available for installation via Library Manager within a day's time.

You can check the logs from the Library Manager indexer for your library(s) here:
http://downloads.arduino.cc/libraries/logs/github.com/ELOWRO/ADS1119/