DISCO_L072CZ_LRWAN1: add a new platform

targets/TARGET_STM/TARGET_STM32L0/TARGET_DISCO_L072CZ_LRWAN1/PeripheralNames.h

@@ -0,0 +1,81 @@
+/* mbed Microcontroller Library
+ *******************************************************************************
+ * Copyright (c) 2017, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+#ifndef MBED_PERIPHERALNAMES_H
+#define MBED_PERIPHERALNAMES_H
+
+#include "cmsis.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+    ADC_1 = (int)ADC1_BASE
+} ADCName;
+
+typedef enum {
+    DAC_1 = (int)DAC_BASE
+} DACName;
+
+typedef enum {
+    UART_1   = (int)USART1_BASE,
+    UART_2   = (int)USART2_BASE,
+    UART_4   = (int)USART4_BASE,
+    UART_5   = (int)USART5_BASE,
+    LPUART_1 = (int)LPUART1_BASE
+} UARTName;
+
+#define STDIO_UART_TX  PA_2
+#define STDIO_UART_RX  PA_3
+#define STDIO_UART     UART_2
+
+typedef enum {
+    SPI_1 = (int)SPI1_BASE,
+    SPI_2 = (int)SPI2_BASE
+} SPIName;
+
+typedef enum {
+    I2C_1 = (int)I2C1_BASE,
+    I2C_2 = (int)I2C2_BASE,
+    I2C_3 = (int)I2C3_BASE
+} I2CName;
+
+typedef enum {
+    PWM_2  = (int)TIM2_BASE,
+    PWM_3  = (int)TIM3_BASE,
+    PWM_21 = (int)TIM21_BASE,
+    PWM_22 = (int)TIM22_BASE
+} PWMName;
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif

targets/TARGET_STM/TARGET_STM32L0/TARGET_DISCO_L072CZ_LRWAN1/PeripheralPins.c

@@ -0,0 +1,213 @@
+/* mbed Microcontroller Library
+ *******************************************************************************
+ * Copyright (c) 2017, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+
+#include "PeripheralPins.h"
+
+// =====
+// Note: Commented lines are alternative possibilities which are not used per default.
+//       If you change them, you will have also to modify the corresponding xxx_api.c file
+//       for pwmout, analogin, analogout, ...
+// =====
+
+//*** ADC ***
+
+const PinMap PinMap_ADC[] = {
+    {PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)},  // ARDUINO A0
+    {PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)},  // Pin not available on any connector
+//  {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)},  // ARDUINO D1 - Used by STDIO_UART_TX
+//  {PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)},  // ARDUINO D0 - Used by STDIO_UART_RX
+    {PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)},  // ARDUINO A2
+    {PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)},  // CN3.7 - Used also to drive LED2
+    {PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)},  // Pin not available on any connector
+    {PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)},  // Pin not available on any connector
+    {PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)},  // Pin not available on any connector
+    {PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)},  // Pin not available on any connector
+    {PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // Pin not available on any connector
+    {PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // Pin not available on any connector
+    {PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // Pin not available on any connector
+    {NC,   NC,    0}
+};
+
+const PinMap PinMap_ADC_Internal[] = {
+    {ADC_TEMP, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 17, 0)}, // Internal channel
+    {ADC_VREF, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,  0, 0)}, // Internal channel
+    {ADC_VBAT, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // Internal channel
+    {NC,       NC,    0}
+};
+
+//*** DAC ***
+
+const PinMap PinMap_DAC[] = {
+    {PA_4, DAC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ARDUINO A2
+    {PA_5, DAC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // CN3.7 - Used also to drive LED2
+    {NC,   NC,    0}
+};
+
+//*** I2C ***
+
+const PinMap PinMap_I2C_SDA[] = {
+    {PA_10, I2C_1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, // ARDUINO D2
+    {PB_4,  I2C_3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF7_I2C3)}, // Pin not available on any connector
+    {PB_7,  I2C_1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)}, // ARDUINO D5 - Used also to drive LED4
+    {PB_9,  I2C_1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, // ARDUINO D14
+    {PB_11, I2C_2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)}, // Pin not available on any connector
+    {PB_14, I2C_2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF5_I2C2)}, // ARDUINO D12
+    {PC_1,  I2C_3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF7_I2C3)}, // Pin not available on any connector
+    {NC,    NC,    0}
+};
+
+const PinMap PinMap_I2C_SCL[] = {
+    {PA_8,  I2C_3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF7_I2C3)}, // ARDUINO D7
+    {PA_9,  I2C_1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, // ARDUINO D8
+    {PB_6,  I2C_1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)}, // ARDUINO D10 - Used also to drive LED3
+    {PB_8,  I2C_1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, // ARDUINO D15
+    {PB_10, I2C_2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)}, // Pin not available on any connector
+    {PB_13, I2C_2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF5_I2C2)}, // ARDUINO D13
+    {PC_0,  I2C_3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF7_I2C3)}, // Pin not available on any connector
+    {NC,    NC,    0}
+};
+
+//*** PWM ***
+// Pins using TIM21 cannot be used as TIM21 is already used by ticker.
+const PinMap PinMap_PWM[] = {
+    {PA_0,      PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)},  // ARDUINO A0
+    {PA_1,      PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)},  // Pin not available on any connector
+//  {PA_2,      PWM_21, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM21, 1, 0)}, // ARDUINO D1 - Used by STDIO_UART_TX
+//  {PA_2,      PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)},  // ARDUINO D1 - Used by STDIO_UART_TX
+//  {PA_3,      PWM_21, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM21, 2, 0)}, // ARDUINO D0 - Used by STDIO_UART_RX
+//  {PA_3,      PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)},  // ARDUINO D0 - Used by STDIO_UART_RX
+    {PA_5,      PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM2, 1, 0)},  // CN3.7 - Used also to drive LED2
+    {PA_6,      PWM_3,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)},  // Pin not available on any connector
+    {PA_6_ALT0, PWM_22, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM22, 1, 0)}, // Pin not available on any connector
+    {PA_7,      PWM_3,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)},  // Pin not available on any connector
+    {PA_7_ALT0, PWM_22, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM22, 2, 0)}, // Pin not available on any connector
+    {PA_15,     PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM2, 1, 0)},  // Pin not available on any connector
+    {PB_0,      PWM_3,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)},  // Pin not available on any connector
+    {PB_1,      PWM_3,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)},  // Pin not available on any connector
+    {PB_3,      PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)},  // Pin not available on any connector
+    {PB_4,      PWM_3,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)},  // Pin not available on any connector
+    {PB_4_ALT0, PWM_22, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM22, 1, 0)}, // Pin not available on any connector
+    {PB_5,      PWM_22, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM22, 2, 0)}, // ARDUINO D4 - Used also to drive LED1
+    {PB_5_ALT0, PWM_3,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM3, 2, 0)},  // ARDUINO D4 - Used also to drive LED1
+    {PB_10,     PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)},  // Pin not available on any connector
+    {PB_11,     PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)},  // Pin not available on any connector
+//  {PB_13,     PWM_21, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_TIM21, 1, 0)}, // ARDUINO D13 - TIM21 used by ticker
+//  {PB_14,     PWM_21, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_TIM21, 2, 0)}, // ARDUINO D12 - TIM21 used by ticker
+    {NC,        NC,     0}
+};
+
+//*** SERIAL ***
+
+const PinMap PinMap_UART_TX[] = {
+    {PA_0,       UART_4,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USART4)},  // ARDUINO A0
+    {PA_2,       UART_2,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART2)},  // ARDUINO D1 - Used by STDIO_UART_TX
+//  {PA_2,       LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, // ARDUINO D1 - UART2 is already used by STDIO_UART_TX
+    {PA_9,       UART_1,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART1)},  // ARDUINO D8
+    {PA_14,      UART_2,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART2)},  // Warning: this pin is used by SWCLK
+    {PA_14_ALT0, LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, // Warning: this pin is used by SWCLK
+    {PB_3,       UART_5,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USART5)},  // Pin not available on any connector
+    {PB_6,       UART_1,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)},  // ARDUINO D10 - Used also to drive LED3
+    {PB_10,      LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_LPUART1)}, // Pin not available on any connector
+    {PB_11,      LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_LPUART1)}, // Pin not available on any connector
+    {PC_1,       LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, // Pin not available on any connector
+    {NC,         NC,       0}
+};
+
+const PinMap PinMap_UART_RX[] = {
+    {PA_1,      UART_4,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USART4)},  // Pin not available on any connector
+    {PA_3,      UART_2,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART2)},  // ARDUINO D0 - Used by STDIO_UART_RX
+//  {PA_3,      LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, // ARDUINO D0 - UART2 is already used by STDIO_UART_RX
+    {PA_10,     UART_1,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART1)},  // ARDUINO D2
+    {PA_13,     LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, // Warning: this pin is used by SWDIO
+    {PA_15,     UART_2,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART2)},  // Pin not available on any connector
+    {PB_4,      UART_5,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USART5)},  // Pin not available on any connector
+    {PB_7,      UART_1,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)},  // ARDUINO D5 - Used also to drive LED4
+    {PB_10,     LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_LPUART1)}, // Pin not available on any connector
+    {PB_11,     LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_LPUART1)}, // Pin not available on any connector
+    {PC_0,      LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, // Pin not available on any connector
+    {NC,        NC,       0}
+};
+
+const PinMap PinMap_UART_RTS[] = {
+    {PA_1,  UART_2,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART2)},  // Pin not available on any connector
+    {PA_12, UART_1,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART1)},  // CN3.14
+    {PA_15, UART_4,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USART4)},  // Pin not available on any connector
+    {PB_1,  LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_LPUART1)}, // Pin not available on any connector
+    {PB_3,  UART_1,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_USART1)},  // Pin not available on any connector
+    {PB_5,  UART_5,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USART5)},  // ARDUINO D4 - Used also to drive LED1
+    {PB_12, LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_LPUART1)}, // ARDUINO D9
+    {PB_14, LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_LPUART1)}, // ARDUINO D12
+    {NC,    NC,       0}
+};
+
+const PinMap PinMap_UART_CTS[] = {
+    {PA_0,  UART_2,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART2)},  // ARDUINO A0
+    {PA_6,  LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_LPUART1)}, // Pin not available on any connector
+    {PA_11, UART_1,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART1)},  // CN3.15
+    {PB_4,  UART_1,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_USART1)},  // Pin not available on any connector
+    {PB_7,  UART_4,   STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USART4)},  // ARDUINO D5 - Used also to drive LED4
+    {PB_13, LPUART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_LPUART1)}, // ARDUINO D13
+    {NC,    NC,       0}
+};
+
+//*** SPI ***
+
+const PinMap PinMap_SPI_MOSI[] = {
+    {PA_7,  SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // Pin not available on any connector
+    {PA_12, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // CN3.14
+    {PB_5,  SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // ARDUINO D4 - Used also to drive LED1
+    {PB_15, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, // ARDUINO D11
+    {NC,    NC,    0}
+};
+
+const PinMap PinMap_SPI_MISO[] = {
+    {PA_6,  SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // Pin not available on any connector
+    {PA_11, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // CN3.15
+    {PB_4,  SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // Pin not available on any connector
+    {PB_14, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, // ARDUINO D12
+    {PC_2,  SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_SPI2)}, // Pin not available on any connector
+    {NC,    NC,    0}
+};
+
+const PinMap PinMap_SPI_SCLK[] = {
+    {PA_5,  SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // CN3.7 - Used also to drive LED2
+    {PB_3,  SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // Pin not available on any connector
+    {PB_10, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, // Pin not available on any connector
+    {PB_13, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, // ARDUINO D13
+    {NC,    NC,    0}
+};
+
+const PinMap PinMap_SPI_SSEL[] = {
+    {PA_4,  SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // ARDUINO A2
+    {PA_15, SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // Pin not available on any connector
+    {PB_9,  SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, // ARDUINO D14
+    {PB_12, SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, // ARDUINO D9
+    {NC,    NC,    0}
+};