New Target: Mbed Connect Cloud board

features/FEATURE_LWIP/lwip-interface/lwip-eth/arch/TARGET_STM/TARGET_STM32F4/TARGET_MBED_CONNECT_ODIN/stm32f4_eth_conf.c

@@ -0,0 +1,61 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2017 ARM Limited
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include "stm32f4xx_hal.h"
+
+void _eth_config_mac(ETH_HandleTypeDef *heth)
+{
+    ETH_MACInitTypeDef macconf =
+    {
+        .Watchdog = ETH_WATCHDOG_ENABLE,
+        .Jabber = ETH_JABBER_ENABLE,
+        .InterFrameGap = ETH_INTERFRAMEGAP_96BIT,
+        .CarrierSense = ETH_CARRIERSENCE_ENABLE,
+        .ReceiveOwn = ETH_RECEIVEOWN_ENABLE,
+        .LoopbackMode = ETH_LOOPBACKMODE_DISABLE,
+        .ChecksumOffload = ETH_CHECKSUMOFFLAOD_ENABLE,
+        .RetryTransmission = ETH_RETRYTRANSMISSION_DISABLE,
+        .AutomaticPadCRCStrip = ETH_AUTOMATICPADCRCSTRIP_DISABLE,
+        .BackOffLimit = ETH_BACKOFFLIMIT_10,
+        .DeferralCheck = ETH_DEFFERRALCHECK_DISABLE,
+        .ReceiveAll = ETH_RECEIVEAll_DISABLE,
+        .SourceAddrFilter = ETH_SOURCEADDRFILTER_DISABLE,
+        .PassControlFrames = ETH_PASSCONTROLFRAMES_BLOCKALL,
+        .BroadcastFramesReception = ETH_BROADCASTFRAMESRECEPTION_ENABLE,
+        .DestinationAddrFilter = ETH_DESTINATIONADDRFILTER_NORMAL,
+        .PromiscuousMode = ETH_PROMISCUOUS_MODE_DISABLE,
+        .MulticastFramesFilter = ETH_MULTICASTFRAMESFILTER_NONE, // Disable multicast filter
+        .UnicastFramesFilter = ETH_UNICASTFRAMESFILTER_PERFECT,
+        .HashTableHigh = 0x0U,
+        .HashTableLow = 0x0U,
+        .PauseTime = 0x0U,
+        .ZeroQuantaPause = ETH_ZEROQUANTAPAUSE_DISABLE,
+        .PauseLowThreshold = ETH_PAUSELOWTHRESHOLD_MINUS4,
+        .UnicastPauseFrameDetect = ETH_UNICASTPAUSEFRAMEDETECT_DISABLE,
+        .ReceiveFlowControl = ETH_RECEIVEFLOWCONTROL_DISABLE,
+        .TransmitFlowControl = ETH_TRANSMITFLOWCONTROL_DISABLE,
+        .VLANTagComparison = ETH_VLANTAGCOMPARISON_16BIT,
+        .VLANTagIdentifier = 0x0U
+    };
+
+    if (heth->Init.ChecksumMode == ETH_CHECKSUM_BY_HARDWARE) {
+        macconf.ChecksumOffload = ETH_CHECKSUMOFFLAOD_ENABLE;
+    } else {
+        macconf.ChecksumOffload = ETH_CHECKSUMOFFLAOD_DISABLE;
+    }
+
+    (void) HAL_ETH_ConfigMAC(heth, &macconf);
+}

features/FEATURE_LWIP/lwip-interface/lwip-eth/arch/TARGET_STM/TARGET_STM32F4/TARGET_MBED_CONNECT_ODIN/stm32f4_eth_init.c

@@ -0,0 +1,143 @@
+#include <string.h>
+#include "stm32f4xx_hal.h"
+#include "mbed_toolchain.h"
+
+#define C029_OTP_START_ADDRESS           (0x1FFF7800U)
+#define C029_OTP_END_ADDRESS             (C029_OTP_START_ADDRESS + (16*32))
+#define C029_MAC_ETHERNET_ID             (3)
+
+typedef MBED_PACKED(struct) C029_OTP_Header {
+    uint8_t id;
+    uint8_t len;
+    uint8_t data[];
+} C029_OTP_Header;
+
+static int _macRetrieved = 0;
+static char _macAddr[6] = { 0x02, 0x02, 0xF7, 0xF0, 0x00, 0x00 };
+
+static C029_OTP_Header *increment(C029_OTP_Header *pTemp)
+{
+    uint8_t len = 0;
+    uint8_t id = 0;
+    uint8_t *p = (uint8_t*)pTemp;
+
+    memcpy((void*)&id, (void*)pTemp, 1);
+
+    if (id == 0xFF){
+        p++;
+    } else {
+        p++;
+        memcpy((void*)&len, (void*)p++, 1);
+        p += len;
+    }
+    return (C029_OTP_Header*)p;
+}
+
+/**
+ * Override HAL Eth Init function
+ */
+void HAL_ETH_MspInit(ETH_HandleTypeDef* heth)
+{
+    GPIO_InitTypeDef GPIO_InitStructure;
+    if (heth->Instance == ETH) {
+
+        /* Enable GPIOs clocks */
+        __HAL_RCC_GPIOA_CLK_ENABLE();
+        __HAL_RCC_GPIOB_CLK_ENABLE();
+        __HAL_RCC_GPIOC_CLK_ENABLE();
+
+        /** ETH GPIO Configuration
+          RMII_REF_CLK ----------------------> PA1
+          RMII_MDIO -------------------------> PA2
+          RMII_MDC --------------------------> PC1
+          RMII_MII_CRS_DV -------------------> PA7
+          RMII_MII_RXD0 ---------------------> PC4
+          RMII_MII_RXD1 ---------------------> PC5
+          RMII_MII_RXER ---------------------> PG2
+          RMII_MII_TX_EN --------------------> PB11
+          RMII_MII_TXD0 ---------------------> PB12
+          RMII_MII_TXD1 ---------------------> PB13
+         */
+        /* Configure PA1, PA2 and PA7 */
+        GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
+        GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
+        GPIO_InitStructure.Pull = GPIO_PULLUP;
+        GPIO_InitStructure.Pin = GPIO_PIN_2 | GPIO_PIN_7;
+        GPIO_InitStructure.Alternate = GPIO_AF11_ETH;
+        HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);
+
+        GPIO_InitStructure.Pull = GPIO_NOPULL;
+        GPIO_InitStructure.Pin = GPIO_PIN_1;
+        HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);
+
+        /* Configure PB13 */
+        GPIO_InitStructure.Pin = GPIO_PIN_13 | GPIO_PIN_11 | GPIO_PIN_12;
+        HAL_GPIO_Init(GPIOB, &GPIO_InitStructure);
+
+        /* Configure PC1, PC4 and PC5 */
+        GPIO_InitStructure.Pin = GPIO_PIN_1 | GPIO_PIN_4 | GPIO_PIN_5;
+        HAL_GPIO_Init(GPIOC, &GPIO_InitStructure);
+
+        /* Enable the Ethernet global Interrupt */
+        HAL_NVIC_SetPriority(ETH_IRQn, 0x7, 0);
+        HAL_NVIC_EnableIRQ(ETH_IRQn);
+
+        /* Enable ETHERNET clock  */
+        __HAL_RCC_ETH_CLK_ENABLE();
+    }
+}
+
+/**
+ * Override HAL Eth DeInit function
+ */
+void HAL_ETH_MspDeInit(ETH_HandleTypeDef* heth)
+{
+    if (heth->Instance == ETH) {
+        /* Peripheral clock disable */
+        __HAL_RCC_ETH_CLK_DISABLE();
+
+        /** ETH GPIO Configuration
+          RMII_REF_CLK ----------------------> PA1
+          RMII_MDIO -------------------------> PA2
+          RMII_MDC --------------------------> PC1
+          RMII_MII_CRS_DV -------------------> PA7
+          RMII_MII_RXD0 ---------------------> PC4
+          RMII_MII_RXD1 ---------------------> PC5
+          RMII_MII_RXER ---------------------> PG2
+          RMII_MII_TX_EN --------------------> PB11
+          RMII_MII_TXD0 ---------------------> PB12
+          RMII_MII_TXD1 ---------------------> PB13
+         */
+        HAL_GPIO_DeInit(GPIOA, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_7);
+        HAL_GPIO_DeInit(GPIOB, GPIO_PIN_13 | GPIO_PIN_11 | GPIO_PIN_12);
+        HAL_GPIO_DeInit(GPIOC, GPIO_PIN_1 | GPIO_PIN_4 | GPIO_PIN_5);
+
+        /* Disable the Ethernet global Interrupt */
+        NVIC_DisableIRQ(ETH_IRQn);
+    }
+}
+
+uint8_t mbed_otp_mac_address(char *mac)
+{
+    C029_OTP_Header *pFound = NULL;
+    C029_OTP_Header *pTemp = (C029_OTP_Header*)C029_OTP_START_ADDRESS;
+    C029_OTP_Header temp;
+
+    if (_macRetrieved == 0) {
+        while ((pTemp >= (C029_OTP_Header*)C029_OTP_START_ADDRESS) && (pTemp < (C029_OTP_Header*)C029_OTP_END_ADDRESS)){
+            memcpy((void*)&temp, (void*)pTemp, sizeof(temp));
+            if (temp.id == C029_MAC_ETHERNET_ID){
+                pFound = pTemp;
+                break;
+            }
+            pTemp = increment(pTemp);
+        }
+        if (pFound != NULL) {
+            memcpy(_macAddr, pFound->data, 6);
+            _macRetrieved = 1;
+        }
+    }
+    memcpy(mac, _macAddr, 6);
+
+    return 1;
+}

features/FEATURE_LWIP/lwip-interface/lwip-eth/arch/TARGET_STM/TARGET_STM32F4/TARGET_UBLOX_EVK_ODIN_W2/stm32f4_eth_conf.c

@@ -19,7 +19,7 @@
 void _eth_config_mac(ETH_HandleTypeDef *heth)
 {
     ETH_MACInitTypeDef macconf =
-        {
+    {
         .Watchdog = ETH_WATCHDOG_ENABLE,
         .Jabber = ETH_JABBER_ENABLE,
         .InterFrameGap = ETH_INTERFRAMEGAP_96BIT,
@@ -48,8 +48,8 @@ void _eth_config_mac(ETH_HandleTypeDef *heth)
         .ReceiveFlowControl = ETH_RECEIVEFLOWCONTROL_DISABLE,
         .TransmitFlowControl = ETH_TRANSMITFLOWCONTROL_DISABLE,
         .VLANTagComparison = ETH_VLANTAGCOMPARISON_16BIT,
-        .VLANTagIdentifier = 0x0U,
-        };
+        .VLANTagIdentifier = 0x0U
+    };
 
     if (heth->Init.ChecksumMode == ETH_CHECKSUM_BY_HARDWARE) {
         macconf.ChecksumOffload = ETH_CHECKSUMOFFLAOD_ENABLE;

features/FEATURE_LWIP/lwip-interface/lwip-eth/arch/TARGET_STM/TARGET_STM32F4/TARGET_UBLOX_EVK_ODIN_W2/stm32f4_eth_init.c

@@ -25,8 +25,7 @@ static C029_OTP_Header *increment(C029_OTP_Header *pTemp)
 
     if (id == 0xFF){
         p++;
-    }
-    else {
+    } else {
         p++;
         memcpy((void*)&len, (void*)p++, 1);
         p += len;
@@ -59,31 +58,30 @@ void HAL_ETH_MspInit(ETH_HandleTypeDef* heth)
           RMII_MII_TXD0 ---------------------> PB12
           RMII_MII_TXD1 ---------------------> PB13
          */
-        /* Configure PA1, PA2 and PA7 */       
+        /* Configure PA1, PA2 and PA7 */
         GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
         GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
         GPIO_InitStructure.Pull = GPIO_PULLUP;
         GPIO_InitStructure.Pin = GPIO_PIN_2 | GPIO_PIN_7;
         GPIO_InitStructure.Alternate = GPIO_AF11_ETH;
         HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);
-        
+
         GPIO_InitStructure.Pull = GPIO_NOPULL;
         GPIO_InitStructure.Pin = GPIO_PIN_1;
         HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);
 
         /* Configure PB13 */
-	    GPIO_InitStructure.Pin = GPIO_PIN_13 | GPIO_PIN_11 | GPIO_PIN_12;
+        GPIO_InitStructure.Pin = GPIO_PIN_13 | GPIO_PIN_11 | GPIO_PIN_12;
         HAL_GPIO_Init(GPIOB, &GPIO_InitStructure);
 
         /* Configure PC1, PC4 and PC5 */
         GPIO_InitStructure.Pin = GPIO_PIN_1 | GPIO_PIN_4 | GPIO_PIN_5;
-	    HAL_GPIO_Init(GPIOC, &GPIO_InitStructure);
-
+        HAL_GPIO_Init(GPIOC, &GPIO_InitStructure);
 
         /* Enable the Ethernet global Interrupt */
         HAL_NVIC_SetPriority(ETH_IRQn, 0x7, 0);
         HAL_NVIC_EnableIRQ(ETH_IRQn);
-        
+
         /* Enable ETHERNET clock  */
         __HAL_RCC_ETH_CLK_ENABLE();
     }