add support for the RAK811

targets/TARGET_STM/TARGET_STM32L1/TARGET_MTB_RAK811/PeripheralNames.h

@@ -0,0 +1,76 @@
+/* mbed Microcontroller Library
+ *******************************************************************************
+ * Copyright (c) 2015, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+#ifndef MBED_PERIPHERALNAMES_H
+#define MBED_PERIPHERALNAMES_H
+
+#include "cmsis.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+    ADC_1 = (int)ADC1_BASE
+} ADCName;
+
+typedef enum {
+    DAC_1 = (int)DAC_BASE
+} DACName;
+
+typedef enum {
+    UART_1 = (int)USART1_BASE,
+    UART_2 = (int)USART2_BASE,
+    UART_3 = (int)USART3_BASE
+} UARTName;
+
+typedef enum {
+    SPI_1 = (int)SPI1_BASE,
+    SPI_2 = (int)SPI2_BASE
+} SPIName;
+
+typedef enum {
+    I2C_1 = (int)I2C1_BASE,
+    I2C_2 = (int)I2C2_BASE
+} I2CName;
+
+typedef enum {
+    PWM_2  = (int)TIM2_BASE,
+    PWM_3  = (int)TIM3_BASE,
+    PWM_4  = (int)TIM4_BASE, // used as us_ticker
+    PWM_9  = (int)TIM9_BASE,
+    PWM_10 = (int)TIM10_BASE,
+    PWM_11 = (int)TIM11_BASE
+} PWMName;
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif

targets/TARGET_STM/TARGET_STM32L1/TARGET_MTB_RAK811/PeripheralPins.c

@@ -0,0 +1,125 @@
+/* mbed Microcontroller Library
+ *******************************************************************************
+ * Copyright (c) 2016, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+
+#include "PeripheralPins.h"
+
+// =====
+// Note: Commented lines are alternative possibilities which are not used per default.
+//       If you change them, you will have also to modify the corresponding xxx_api.c file
+//       for pwmout, analogin, analogout, ...
+// =====
+
+//*** ADC ***
+
+const PinMap PinMap_ADC[] = {
+    {PB_12, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // ADC_IN18
+    {PB_14, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 20, 0)}, // ADC_IN20
+    {PB_15, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 21, 0)}, // ADC_IN21
+    {NC,    NC,    0}
+};
+
+const PinMap PinMap_ADC_Internal[] = {
+    {ADC_TEMP, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)},
+    {ADC_VREF, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 17, 0)},
+    {NC,    NC,    0}
+};
+
+//*** DAC ***
+
+const PinMap PinMap_DAC[] = {
+    {NC,   NC,    0}
+};
+
+//*** I2C ***
+
+const PinMap PinMap_I2C_SDA[] = {
+    {PB_9,  I2C_1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
+    {PB_11, I2C_2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
+    {NC,    NC,    0}
+};
+
+const PinMap PinMap_I2C_SCL[] = {
+    {PB_8,  I2C_1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
+    {PB_10, I2C_2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
+    {NC,    NC,    0}
+};
+
+//*** PWM ***
+
+// TIM5 cannot be used because already used by the us_ticker.
+const PinMap PinMap_PWM[] = {
+    {PB_10, PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)},  // TIM2_CH3
+    {PB_11, PWM_2,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)},  // TIM2_CH4
+    {NC,    NC,     0}
+};
+
+//*** SERIAL ***
+
+const PinMap PinMap_UART_TX[] = {
+    {PA_2,  UART_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
+    {PA_9,  UART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
+    {PB_10, UART_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
+    {NC,    NC,     0}
+};
+
+const PinMap PinMap_UART_RX[] = {
+    {PA_10, UART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
+    {PB_11, UART_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
+    {NC,    NC,     0}
+};
+
+//*** SPI ***
+
+const PinMap PinMap_SPI_MOSI[] = {
+    {PA_7,      SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+    {PA_12,     SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+    {PB_5,      SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+    {PB_15,     SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+    {NC,        NC,    0}
+};
+
+const PinMap PinMap_SPI_MISO[] = {
+    {PA_6,      SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+    {PB_4,      SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+    {PB_14,     SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+    {NC,        NC,    0}
+};
+
+const PinMap PinMap_SPI_SCLK[] = {
+    {PA_5,      SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+    {PB_3,      SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+    {NC,        NC,    0}
+};
+
+const PinMap PinMap_SPI_SSEL[] = {
+    {PA_15,     SPI_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
+    {PB_12,     SPI_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+    {NC,        NC,    0}
+};

targets/TARGET_STM/TARGET_STM32L1/TARGET_MTB_RAK811/PinNames.h

@@ -0,0 +1,148 @@
+/* mbed Microcontroller Library
+ *******************************************************************************
+ * Copyright (c) 2016, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+#ifndef MBED_PINNAMES_H
+#define MBED_PINNAMES_H
+
+#include "cmsis.h"
+#include "PinNamesTypes.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+    PA_0  = 0x00,
+    PA_1  = 0x01,
+    PA_2  = 0x02,
+    PA_3  = 0x03,
+    PA_4  = 0x04,
+    PA_5  = 0x05,
+    PA_6  = 0x06,
+    PA_7  = 0x07,
+    PA_8  = 0x08,
+    PA_9  = 0x09,
+    PA_10 = 0x0A,
+    PA_11 = 0x0B,
+    PA_12 = 0x0C,
+    PA_13 = 0x0D,
+    PA_14 = 0x0E,
+    PA_15 = 0x0F,
+
+    PB_0  = 0x10,
+    PB_1  = 0x11,
+    PB_2  = 0x12, // not used
+    PB_3  = 0x13,
+    PB_4  = 0x14,
+    PB_5  = 0x15,
+    PB_6  = 0x16,
+    PB_7  = 0x17,
+    PB_8  = 0x18,
+    PB_9  = 0x19,
+    PB_10 = 0x1A,
+    PB_11 = 0x1B,
+    PB_12 = 0x1C,
+    PB_13 = 0x1D,
+    PB_14 = 0x1E,
+    PB_15 = 0x1F,
+
+    PC_13 = 0x2D,
+    PC_14 = 0x2E, // not used ?
+    PC_15 = 0x2F, // not used ?
+
+    PH_0  = 0x70,
+    PH_1  = 0x71, // not used ?
+
+    // ADC internal channels
+    ADC_TEMP = 0xF0,
+    ADC_VREF = 0xF1,
+
+    ADC1_0   = PB_14,
+    ADC1_1   = PB_15,
+    ADC1_2   = PB_12,
+
+    UARTn_RX = PA_10,
+    UARTn_TX = PA_9,
+
+    SPI_RF_MOSI = PA_7,
+    SPI_RF_MISO = PA_6,
+    SPI_RF_SCK  = PA_5,
+    SPI_RF_CS   = PB_0,
+    SPI_RF_RESET= PB_13,
+
+    DIO0        = PA_11,
+    DIO1        = PB_1,
+    DIO2        = PA_3,
+    DIO3        = PH_0,
+    DIO4        = PC_13,
+    //DIO5        = ,
+
+    ANT_CTX_PA  = PA_4,
+    ANT_CRX_RX  = PB_6,
+    ANT_CBT_HF  = PB_7,
+    RF_TCXO_EN  = PH_1,
+
+    SPI_MISO    = PB_4,
+    SPI_MOSI    = PB_5,
+    SPI_SCK     = PB_3,
+    FLASH_CS    = PA_15,
+
+    I2C_SCL     = PB_8,
+    I2C_SDA     = PB_0,
+
+    LCD_A0      = PA_8,
+    LCD_nCS     = PA_1,
+    LCD_nRESET  = PA_2,
+
+    // Generic signals namings
+    LED1        = PA_12, // red
+    LED2        = PB_10, // blue
+    LED3        = PB_11, // green
+    USER_BUTTON = PA_0,
+
+    STDIO_UART_RX = PA_10,
+    STDIO_UART_TX = PA_9,
+
+    // aliases
+    POT         = ADC1_2,
+    BUTTON1     = USER_BUTTON,
+    SERIAL_TX   = STDIO_UART_TX,
+    SERIAL_RX   = STDIO_UART_RX,
+    USBTX       = STDIO_UART_TX,
+    USBRX       = STDIO_UART_RX,
+
+    // Not connected
+    NC = (int)0xFFFFFFFF
+} PinName;
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif